top of page

Window film instalation

​

What you’ll need to apply window film 

 

You will need:

​

·         a soft and clean cloth for cleaning

·         a scraper

·         a hard rubber spatula

·         a water nebulizer

·         a metal ruler

·         a metal bracket

·         a regular cutter/a cutter with a steel blade

·         a spatula

·         a paper towel 

 

Installation conditions: the requirements

​

In addition to making sure you have all the tools you need, you should also make sure that the conditions are right before applying any glass film. First of all, the glass surface needs to be perfectly smooth and in good condition, as well as clean. Secondly, the temperature for installation is mentioned under the section "installation temperatures", according to the product.; you should also try to pick a windless day, without any draughts – they could make the application of solar film difficult, as well as carrying dust which could slip between the glass and the film itself. 

​

Before applying the solar control film: cleaning the glass

​

As mentioned, a fundamental requirement is a perfectly clean glass surface. The glass must be cleaned using a detergent which leaves no residue behind, such as lanolin or wax; similarly, the cloth used for cleaning and drying the glass must not shed any fibres. To ensure that the glass is perfectly clean and free of contaminants, after carefully cleaning it, it is a good idea to carry out a last wipe-through with a scraper, paying close attention to the corners and sides near the profiles of the fixtures. At this point, you can switch to the application of the solar glass film!

​

Instructions for applying solar glass film, step by step

 

​

1.       The previously cleaned glass, should be wetted slightly and evenly, using a water nebulizer;

2.       Now, it is possible to stretch out the film, operating in reverse, thus holding the liner towards yourself; thanks to the water on the glass, the film will remain “hanging” on the glass surface

3.       You can now remove the protective liner;

4.       Now, you have a film ready to be “activated”: with the nebulizer, wet its surface abundantly, “activating” the adhesive surface (in fact water will make it possible to remove the water-soluble patina that protecting the adhesive). After about two minutes, the adhesive will be completely uncovered and ready to use;

5.       Turn the solar film, laying the adhesive part to the glass, misting abundantly;

6.       Adjust the position of the film which, thanks to the water below, will be easily repositionable;

7.       To make the film adhere perfectly, start to spread the film through the spatula (to slide the spatula perfectly, you can help yourself with a little water mixed with a few drops of mild soap)

8.       At this point, you can trim the film – using a ruler, a bracket and a cutter – making sure to leave 2 mm between the film and the side rubber of the frame;

9.       Now, use the spatula on the film again, pressing down more strongly, to perfect the application;

10.   At this point, you can use the spatula and a paper cloth to make sure the edges adhere perfectly.

 

The solar film application is now completed: following these steps, you’ll be able to apply these protections on all windows of a building.

​

After applying the solar film

It should be noted that the adhesive of fixture solar films completes its drying in about 8 weeks. It is therefore best to wait at least two weeks before proceeding with a possible cleaning of the glass, to avoid the risk of compromising the application work.

​

After 8 weeks use the sealant to cover the 2 mm crack. Do not use the sealant before this! Bubbles may occur in that case.

​

Installation temperatures?

​

SD2500 and SD 1000

​

+ 6°C... + 30°C ambient temperature and window surface temp. of + 6°C ... + 24°C.

​

YSHIELD RDF films

 + 10°C. .. + 25°C ambient and glass surface temp.

​

What material can the film be installed on?

Glass, either toughened or float glas, in some cases laminated glass is ok. The film does not stay on polycarbonate or acrylic windows, nor on liquid surface windows. Contact us before purchase  if you are even a bit unsure of compability.

​

Can I film cornered windows?

Yes, but contact us for info regarding this as there are certain things to take into consideration.

​

​​

My window is bigger than the film, how do I aplly the film?

Yo install the film with a but joint and seal the contact area after 8 weeks of dry time.

​

When can I use a sealant?

No earlier than 8 weeks post installation.

​

Do i need to seal the crack between window pane and film?

Yes, it both improves the dampening effect and protects the film.

​​

What sealant should I use?

3M sealant laquer, Dowsil Dow 995 ori YSHIELD FL4 .

​

How do I clean and maintain the films?

Care and maintenance, PDF

​

bottom of page